characteristic / test conditionsdrain-source breakdown voltage (v gs = 0v, i d = 250a) on state drain current 2 (v ds > i d(on) x r ds(on) max, v gs = 10v) drain-source on-state resistance 2 (v gs = 10v, 0.5 i d[cont.] ) zero gate voltage drain current (v ds = v dss , v gs = 0v) zero gate voltage drain current (v ds = 0.8 v dss , v gs = 0v, t c = 125c) gate-source leakage current (v gs = 30v, v ds = 0v) gate threshold voltage (v ds = v gs , i d = 2.5ma) 050-5555 rev c 6-2004 maximum ratings all ratings: t c = 25c unless otherwise specified. symbol v dss i d i dm v gs v gsm p d t j ,t stg t l i ar e ar e as parameterdrain-source voltage continuous drain current @ t c = 25c pulsed drain current 1 gate-source voltage continuousgate-source voltage transient total power dissipation @ t c = 25c linear derating factoroperating and storage junction temperature range lead temperature: 0.063" from case for 10 sec. avalanche current 1 (repetitive and non-repetitive) repetitive avalanche energy 1 single pulse avalanche energy 4 unit volts amps volts watts w/c c amps mj static electrical characteristics symbol bv dss i d(on) r ds(on) i dss i gss v gs(th) unit volts amps ohms ana volts min typ max 300 76 0.040 250 1000100 24 apt30m40b2vfr_lvfr 300 76 304 3040 520 4.16 -55 to 150 300 7650 2500 power mos v ? is a new generation of high voltage n-channel enhancement mode power mosfets. this new technology minimizes the jfet effect,increases packing density and reduces the on-resistance. power mos v ? also achieves faster switching speeds through optimized gate layout. fast recovery body diode avalanche energy rated lower leakage t-max? or to-264 package faster switching caution: these devices are sensitive to electrostatic discharge. proper handling procedures should be followed. apt website - http://www.advancedpower.com power mos v ? fredfet t-max ? to-264 b2vfr lvfr apt30m40b2vfr apt30m40lvfr 300v 76a 0.040 ?? ?? ? g d s downloaded from: http:///
dynamic characteristics apt30m40b2vfr_lvfr 050-5555 rev c 6-2004 z jc , thermal impedance (c/w) 10 -5 10 -4 10 -3 10 -2 10 -1 1.0 10 rectangular pulse duration (seconds) figure 1, maximum effective transient thermal impedance, junction-to-case vs pulse duration 0.30.1 0.050.01 0.0050.001 note: duty factor d = t 1 / t 2 peak t j = p dm x z jc + t c t 1 t 2 p dm 0.1 single pulse 0.02 0.05 0.2 d=0.5 0.01 source-drain diode ratings and characteristics characteristic / test conditionscontinuous source current (body diode) pulsed source current 1 (body diode) diode forward voltage 2 (v gs = 0v, i s = -i d [cont.]) peak diode recovery dv / dt 5 reverse recovery time(i s = -i d [cont.], di / dt = 100a/s) reverse recovery charge(i s = -i d [cont.], di / dt = 100a/s) peak recovery current(i s = -i d [cont.], di / dt = 100a/s) symbol i s i sm v sd dv / dt t rr q rr i rrm unit amps volts v/ns ns c amps symbol c iss c oss c rss q g q gs q gd t d (on) t r t d (off) t f characteristicinput capacitance output capacitance reverse transfer capacitance total gate charge 3 gate-source charge gate-drain ("miller") charge turn-on delay time rise time turn-off delay time fall time test conditions v gs = 0v v ds = 25v f = 1 mhz v gs = 10v v dd = 0.5 v dss i d = i d [cont.] @ 25c v gs = 15v v dd = 0.5 v dss i d = i d [cont.] @ 25c r g = 0.6 ? min typ max 8500 10200 1500 2100 390 585 285 425 56 85 120 180 16 32 20 40 48 72 48 unit pf nc ns min typ max 76 304 1.3 5 t j = 25c 240 t j = 125c 500 t j = 25c 1.1 t j = 125c 5.2 t j = 25c 12 t j = 125c 22 1 repetitive rating: pulse width limited by maximum junction 3 see mil-std-750 method 3471 temperature. 4 starting t j = +25c, l = 870h, r g = 25 ? , peak i l = 76a 2 pulse test: pulse width < 380 s, duty cycle < 2% 5 i s - -i d [cont.], di / dt = 100a/s, v dd - v dss , t j - 150c, r g = 2.0 ? , v r = 200v. apt reserves the right to change, without notice, the specifications and information contained herein. thermal characteristics symbol r jc r ja min typ max 0.24 40 unitc/w characteristicjunction to case junction to ambient downloaded from: http:///
v ds , drain-to-source voltage (volts) v ds , drain-to-source voltage (volts) figure 2, typical output characteristics figure 3, typical output characteristics v gs , gate-to-source voltage (volts) i d , drain current (amperes) figure 4, typical transfer characteristics figure 5, r ds (on) vs drain current t c , case temperature (c) t j , junction temperature (c) figure 6, maximum drain current vs case temperature figure 7, breakdown voltage vs temperature t j , junction temperature (c) t c , case temperature (c) figure 8, on-resistance vs. temperature figure 9, threshold voltage vs temperature r ds (on), drain-to-source on resistance i d , drain current (amperes) i d , drain current (amperes) i d , drain current (amperes) (normalized) v gs (th), threshold voltage bv dss , drain-to-source breakdown r ds (on), drain-to-source on resistance i d , drain current (amperes) (normalized) voltage (normalized) 0 3 06 0 9 01 2 01 5 0 0123456 02468 04 08 01 2 01 6 02 0 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 apt30m40b2vfr_lvfr i d = 0.5 i d [cont.] v gs = 10v 150120 9060 30 0 1.31.2 1.1 1.0 0.9 0.8 1.201.15 1.10 1.05 1.00 0.95 0.90 1.21.1 1.0 0.9 0.8 0.7 0.6 150 120 9060 30 0 150120 9060 30 0 8060 40 20 0 2.52.0 1.5 1.0 0.5 0.0 050-5555 rev c 6-2004 v ds > i d (on) x r ds (on)max. 250sec. pulse test @ <0.5 % duty cycle 5v 4.5v 4v v gs =6.5v, 7v, 10v & 15v v gs =15v v gs =10v t j = +25c t j = -55c t j = +125c t j = +125c t j = +25c v gs =6.5v & 7v 5.5v v gs =10v 6v 5v 4.5v 4v 5.5v 6v v gs =20v t j = -55c normalized to v gs = 10v @ 0.5 i d [cont.] downloaded from: http:///
v ds , drain-to-source voltage (volts) v ds , drain-to-source voltage (volts) figure 10, maximum safe operating area figure 11, typical capacitance vs drain-to-source voltage q g , total gate charge (nc) v sd , source-to-drain voltage (volts) figure 12, gate charges vs gate-to-source voltage figure 13, typical source-drain diode forward voltage v gs , gate-to-source voltage (volts) i d , drain current (amperes) i dr , reverse drain current (amperes) c, capacitance (pf) 1 5 10 50 100 300 .01 .1 1 10 50 0 100 200 300 400 500 0 0.4 0.8 1.2 1.6 2.0 apt30m40b2vfr_lvfr t c =+25c t j =+150c single pulse 400100 5010 51 .5.1 2016 12 84 0 050-5555 rev c 6-2004 operation here limited by r ds (on) t j =+150c t j =+25c c rss c oss c iss 30,00010,000 5,0001,000 500100 400 100 5010 51 v ds =150v v ds =60v v ds =240v i d = i d [cont.] 10s1ms 10ms 100ms dc 100s apts products are covered by one or more of u.s.patents 4,895,810 5,045,903 5,089,434 5,182,234 5,019,522 5,262,336 6,503,786 5,256,583 4,748,103 5,283,202 5,231,474 5,434,095 5,528,058 and foreign patents. us and foreign patents pending. all rights reserved. 15.49 (.610)16.26 (.640) 5.38 (.212)6.20 (.244) 4.50 (.177) max. 19.81 (.780)20.32 (.800) 20.80 (.819)21.46 (.845) 1.65 (.065)2.13 (.084) 1.01 (.040)1.40 (.055) 5.45 (.215) bsc 2.87 (.113)3.12 (.123) 4.69 (.185)5.31 (.209) 1.49 (.059) 2.49 (.098) 2.21 (.087)2.59 (.102) 0.40 (.016)0.79 (.031) drain source gate these dimensions are equal to the to-247 without the mounting hole. drain 2-plcs. 19.51 (.768)20.50 (.807) 19.81 (.780)21.39 (.842) 25.48 (1.003)26.49 (1.043) 2.29 (.090) 2.69 (.106) 0.76 (.030)1.30 (.051) 3.10 (.122) 3.48 (.137) 4.60 (.181)5.21 (.205) 1.80 (.071) 2.01 (.079) 2.59 (.102) 3.00 (.118) 0.48 (.019)0.84 (.033) drain source gate dimensions in millimeters and (inches) drain 2.29 (.090)2.69 (.106) 5.79 (.228)6.20 (.244) 2.79 (.110)3.18 (.125) 5.45 (.215) bsc 2-plcs. dimensions in millimeters and (inches) t-max tm (b2) package outline (b2vfr) to-264 (l) package outline (lvfr) downloaded from: http:///
|
